TOPODRONE LiDAR to mobile mount installation

To install the TOPODRONE LiDAR on the mobile mount, you will need the following components included in the kit:

1.  TOPODRONE LiDAR - 1 pc. 2.  Mobile mount base - 1 pc.. 3.  Mobile mount arm - 3 pc. 4.  Mobile mount suction cup - 3 pc. 5.  GNSS antenna - 1 pc. 6.  Pole (30 cm) - 1 pc. 7.  M3x10 screw - 10 pc. 8.  М5х10 screw - 2 pc.

9.    5/8" - 11 UNC  x 3/4" screw - 1 pc. 10.  TOPODRONE LiDAR spacer - 2 pc. 11.  Hex 2.5 screwdriver - 1 pc. 12.  Hex 4 screwdriver - 1 pc. 13.  Antenna cable - 1 pc. 14.  LEMO 6 PIN - USB Type-C power cable - 1 pc. 15.  Power Bank - 1 pc.

It is strongly recommended to use a TOPODRONE LiDAR protective soft cover for to avoid the risk of damaging the laser scanning lens! For better clarity, in the photos shown, the TOPODRONE TOPODRONE LiDAR is shown without the case.

1. Install the two mobile mount spacers on the TOPODRONE LiDAR laser scanner with 8 M3x10 screws using a Hex 2.5 screwdriver as shown in the photo:

2. Install TOPODRONE LiDAR on the main part of the mobile mount with two M5x10 screws using a Hex 4 screwdriver. Be extremely careful at this step!

Hold the TOPODRONE laser scanner so that it does not fall and proceed to step 3. Use the cover to protect the lens! It is especially important in this step!

3. Set the TOPODRONE laser scanner (1) at the required angle on the main part of the mobile mount (2) and fix the position with two M3x10 screws (7) using a Hex 2.5 screwdriver (11).

4. Connect the mobile mount beam to the suction cup swivel mechanism, repeat with all parts. 

5. Connect the mobile mount beam with the other side to the hinge mechanism of the mobile mount main attachment. If necessary, manually loosen or tighten the thumbscrew. Once the hinge mechanisms are in alignment, manually tighten the thumbscrew.

6. Firmly install the milestone using the screw in the outermost compartment of the main part of the mobile mount.

7. Screw the GNSS antenna (5) onto the pole (6).

8. Connect the GNSS cable (13) to the GNSS antenna (5), taking care not to bend it.

9. Connect the antenna cable with the LEMO connector (13) to the TOPODRONE LiDAR (1) it clicks into place.

10. It is recommended to fix the antenna cable in the area of the pole (6) with a GNSS cable velcro (13) as shown in the photo.

10. ПротритеWipe поверхностьor автомобиляclean влажнымиthe иsurface сухимиof салфетками.the Снимитеvehicle сwith присосокwet защитныеand колпаки.dry Установитеcloths. мобильноеRemove креплениеthe наprotective автомобильcaps приfrom помощиthe присосокsuction приcups. помощиInstall помпы.the Важно!mobile Нельзяmount устанавливатьon присоскиthe наcar загрязнённыеwith пыльныеthe поверхности,suction аcups такusing жеthe наpump. стыкиImportant: плоскостейDo иnot деталей,install гдеthe естьsuction швыcups иon зазоры.dirty, Наdusty приведённыхsurfaces, фотографияхas нижеwell показанas процессon откачкиjoints воздухаof изplanes присосок,and колпакиparts присосокwith неseams сняты.and gaps. The photos below show the process of pumping the air out of the suction cups without removing the suction cup caps.

11. ПодсоединитеConnect кабель питанияthe LEMO к6-Pin лазерномуconnector сканеруof доpower лёгкогоcable щелчка.(14) to the TOPODRONE LiDAR (1), it clicks into place.

12. ПриIf необходимости,necessary, используяuse барашкиthe лучей,beam отрегулируйтеwrenches положениеto мобильногоadjust крепленияthe наposition автомобиле,of чтоthe быmobile оноmount стоялоon ровно.the Наvehicle фотографиях,so приведенныхthat нижеit показаныis вариантыlevel. установкиThe лазерногоphotos сканераbelow show how to mount the TOPODRONE 100+ наlaser автомобильscanner подon угламиthe vehicle at 30 иand 0 градусовdegrees соответственно.respectively.
Примечание:Note: наin приведённыхthe фотографияхphotos использованаbelow, нестандартнаяa веха длиннойnon-standard 20 см,cm отличнаяlong отmilestone поставляемойis вused, комплектеwhich поставки.is different from the one supplied.

12.13. ПодсоединитеConnect кабельthe кUSB-C port oft the power cable (14) to the Power Bank и(15) подайтеand питание.apply Дождитесьpower. инициализацииWait лазерногоfor сканераthe TOPODRONE.TOPODRONE LiDAR to initialize.

РекомендуетсяIt проверятьis надежностьrecommended сцепленияto присокcheck сthe поверхностьюgrip автомобиляof каждыйthe час,suction особенноcups приevery отрицательныхhour, температурахespecially воздуха!at sub-zero temperatures!