Setting the shooting options

Setting shooting parameters

All camera parameters are required for correct calculation of longitudinal and transverse overlap between images during mission planning and en-route imaging.

The focal length value may vary depending on the lens used.

Adjusting the parameters using the Smart Controller

1. Once your aircraft is powered on, the camera will be powered up, initialized and displayed as a TOPODRONE payload in the DJI Pilot 2 app.
2. To activate the camera control buttons, press the AF button on the remote control screen, then press the MF button. These buttons are responsible for auto and manual focus.
3. Photogrammetric camera TOPODRONE P61 works in shutter speed priority mode, the user needs to select shutter speed manually, and the aperture changes depending on the illumination of the object.
4. To set the required shutter speed, use the control roller. Rotating the roller clockwise will decrease the shutter speed and counterclockwise will increase the shutter speed. The shutter speed will be displayed on the screen.
5. To change the ISO setting, press the down button on the control roller, then use the roller to select the desired value and confirm your selection by pressing the center button on the control roller.
6. Pressing right on the control roller opens a menu where you can change exposure steps and confirm changes by pressing the center button.
7. To change the white balance, press the “Fn” button on the camera, select “White Balance”, then use the roller to set the value you want.
8. Check the initialization on the TOPODRONE UAV PPK UPGRADE Kit or on your laser scanner. The LED indication for TOPODRONE UAV PPK UPGRADE Kit is shown in the table below.
   

   LED light	Description
   Green LED	Indicates the status of the Power Module
   Blue LED	PDOP>10 not lit Flashing slowly 3<PDOP<10 Flashing rapidly 2<PDOP PDOP illuminates continuously
   Orange LED	Indicates the status of recording to the memory card. The LED blinks rapidly during recording. Each blinking corresponds to the recording of 4 kB of data
   Red LED	Indicates if there are any errors in the system. If an error occurs, check the memory card

   
   
9. Raise the drone to operating altitude, focus on the ground surface in “AF” mode and set the camera to “MF” mode. Launch the drone for the mission.

It is necessary to repeat all points before each flight.

Customizing shooting settings using a Wi-Fi connection

The camera has an option to display the image on the screen of your mobile device.

After you turn on the camera, an access point with the name of the Wi-Fi network - TD_61mp - will appear. You can connect to the network using the password: topodrone.

After successful connection to the network in the browser window you should enter the address: 192.168.10.1

Recommended range of shooting parameters for TOPODRONE P61

Parameter	Sunny	Cloudy	Overcast
ISO	100 … 200	200 … 600	600 … 800
Shutter speed	1/4000 … 1/2000	1/2000 … 1/1000	1/1000 … 1/800
Aperture	8 … 10	6 … 8	4 … 8
White Balance	Sunny	Cloudy	Cloudy

For more information on customizing your shooting settings, check out our Telegram channel at the links below:

Настройка изображения камеры. Введение. Часть 1 из 3

Настройка изображения камеры. Введение. Часть 2 из 3

Настройка изображения камеры. Введение. Часть 3 из 3

ВыводOutput TOPODRONE P61 вto сетьthe интернетInternet дляto выполненияperform диагностикиdiagnostics

ДляTo выполненияbring процедуры вывода камерыthe TOPODRONE P61 вcamera сетьto интернетthe приInternet, выполненииthe диагностикиfollowing потребуютсяconditions следующиеwill компонентыbe иrequired условия:when performing diagnostics:

1. МобильноеMobile устройствоdevice (смартфонsmartphone илиor планшет)tablet) под управлением ОСrunning Android OS (Протестированы только телефоны маркиOnly Samsung, Honor, Xiaomi мобильныеphones устройстваare остальныхtested, производителейother могутmanufacturers' работатьmobile некорректно)devices may not work correctly)
2. 3G/4G/5G мобильныйmobile интернетinternet илиor Wi-Fi сетьnetwork сwith подключениемinternet к сети Интернетconnection.
3. КабельUSB to LEMO 6 PIN cable
4. USB cable for connection to mobile device.
5. TOPODRONE P61 photogrammetric camera
6. Drone for power connection via cable from Skyport connector
7. Install the TOPODRONE P61 camera according to your delivery set
8. Power up the TOPODRONE P61 by connecting it to the drone.
9. Wait for the camera to turn on and load.
10. Connect the USB – LEMO 6 PIN (поставляетсяcable вместеand сthe TOPODRONE P61)
11. USB кабельcable дляfor подключенияconnecting кto мобильномуa устройствуmobile device together via the USB Type-A connector (поставляетсяrectangular вместе со смартфоном/планшетом)
12. Фотограмметрическая камера TOPODRONE P61
13. Летательный аппарат для подключения питания через кабель от разъема Skyport
14. Установите камеру TOPODRONE P61 в соответствии с вашим комплектом поставки
15. Включите питание TOPODRONE P61, подключив его к дронуconnector).
16. ДождитесьConnect включения и загрузки камеры.
17. Соедините кабельthe USB –to LEMO 6 PIN иcable USBto кабель для подключения к мобильному устройству вместе через разъем USB Type-A (прямоугольный разъем)
18. Подсоедините кабель USB –the LEMO 6 PIN кconnector разъемуof LEMO 6 PIN камерыthe TOPODRONE P61 camera.
19. ПодсоединитеConnect the Android mobile device via USB кабель для подключения к мобильному устройству к мобильному устройству (смартфону или планшету) под управлением ОС Androidcable
20. Убедитесь,Make чтоsure наyour мобильномmobile устройствеdevice имеетсяhas активноеan подключениеactive кInternet сетиconnection Интернет черезvia 3G/4G/5G или черезor Wi-Fi.
21. НаOn мобильномyour устройствеmobile зайдитеdevice, вgo меню:to настройкиthe menu: settings / подключенияconnections / мобильнаяmobile точкаhotspot доступаand и модемmodem / режимUSB USB-модема.modem mode.
22. Камера TOPODRONE P61 выведенаcamera вis сетьdisplayed интернет.on the Internet.